| key | action | source |
|---|---|---|
| + |
Zoom In 20% Zoom(-1.2) | menu-default.lht |
| , |
Cycle object being dragged CycleDrag() | menu-default.lht |
| - |
Zoom Out 20% Zoom(+1.2) | menu-default.lht |
| . |
'All-direction' lines conf(toggle, editor/all_direction_lines, design) | menu-default.lht |
| / |
Cycle line clip/refraction Display(CycleClip) | menu-default.lht |
| : |
Command Entry Command() | menu-default.lht |
| [ |
Previous grid Grid(down) | menu-default.lht |
| \ |
Full screen fullscreen(toggle) | menu-default.lht |
| ] |
Next grid Grid(up) | menu-default.lht |
| a a |
Start routing an arc Tool(Save); Tool(arc); Tool(Press) | menu-default.lht |
| a b a-shift |
Add subcircuits to netlist BaSubc(selected, add) | menu-default.lht |
| a b a |
Add subcircuit to netlist BaSubc(object, add) | menu-default.lht |
| a b f |
Replace selected footprints ReplaceFootprint() | menu-default.lht |
| a b r-shift |
Remove subcircuits from netlist BaSubc(selected, remove) | menu-default.lht |
| a b r |
Remove subcircuit from netlist BaSubc(object, remove) | menu-default.lht |
| a b s |
Swap nets on two selected pins net(swap) | menu-default.lht |
| a b x |
netlist patch for back annotation SavePatch() | menu-default.lht |
| a d a |
Disperse all subcircuits DisperseElements(All) | menu-default.lht |
| a d s |
Disperse selected subcircuits DisperseElements(Selected) | menu-default.lht |
| a l |
Start routing a line Tool(Save); Tool(line); Tool(Press) | menu-default.lht |
| a m |
Place mark MarkCrosshair() | menu-default.lht |
| a o a |
Auto-Optimize djopt(auto) | djopt-menu.lht |
| a o d |
Debumpify djopt(debumpify) | djopt-menu.lht |
| a o m |
Miter djopt(miter) | djopt-menu.lht |
| a o n |
Vianudge djopt(vianudge) | djopt-menu.lht |
| a o o |
Ortho pull djopt(orthopull) | djopt-menu.lht |
| a o p |
Puller Puller() | puller-menu.lht |
| a o s |
Simple optimization djopt(simple) | djopt-menu.lht |
| a o t |
Viatrim djopt(viatrim) | djopt-menu.lht |
| a o u |
Unjaggy djopt(unjaggy) | djopt-menu.lht |
| a p s |
Auto-place selected subcircuits AutoPlaceSelected() | menu-default.lht |
| a r a |
Auto-route all rats AutoRoute(AllRats) | menu-default.lht |
| a r r |
Rip up all auto-routed tracks RipUp(All) | menu-default.lht |
| a r s |
Auto-route selected rats AutoRoute(SelectedRats) | menu-default.lht |
| a r t |
Rip up selected auto-routed tracks RipUp(Selected) | menu-default.lht |
| a v |
Place via Tool(Save); Tool(via); Tool(Press); Tool(Restore) | menu-default.lht |
| a w |
Place mark MarkCrosshair() | menu-default.lht |
| a x |
Design Rule Checker DRC() | menu-default.lht |
| b 1 |
Select Buffer #1 PasteBuffer(1) | menu-default.lht |
| b 2 |
Select Buffer #2 PasteBuffer(2) | menu-default.lht |
| b 3 |
Select Buffer #3 PasteBuffer(3) | menu-default.lht |
| b 4 |
Select Buffer #4 PasteBuffer(4) | menu-default.lht |
| b 5 |
Select scratchpad PasteBuffer(5) | menu-default.lht |
| b b |
Layer bindings... LayerBinding(buffer) | menu-default.lht |
| b c c |
Clear buffer PasteBuffer(Clear) | menu-default.lht |
| b c e |
Convert buffer to extended object... ExtobjConvFrom(buffer, @gui); Tool(buffer) | menu-default.lht |
| b c p |
Convert buffer to padstack PadstackConvert(buffer); Tool(buffer) | menu-default.lht |
| b c s |
Convert buffer to subcircuit PasteBuffer(ConvertSubc) | menu-default.lht |
| b f l |
Load buffer content from file PasteBuffer(Clear); PasteBuffer(LoadAll) | menu-default.lht |
| b f s |
Save buffer content to file PasteBuffer(SaveAll) | menu-default.lht |
| b m l |
Mirror buffer (left/right) Tool(buffer); PasteBuffer(Rotate,1); PasteBuffer(Mirror); PasteBuffer(Rotate,3) | menu-default.lht |
| b m u |
Mirror buffer (up/down) Tool(buffer); PasteBuffer(Mirror) | menu-default.lht |
| b n |
Normalize Tool(buffer); PasteBuffer(Normalize) | menu-default.lht |
| b r a |
Arbitrarily Rotate Buffer Tool(buffer); FreeRotateBuffer() | menu-default.lht |
| b r l |
Rotate buffer 90 deg CCW (left) Tool(buffer); PasteBuffer(Rotate,1) | menu-default.lht |
| b r r |
Rotate buffer 90 deg CW (right) Tool(buffer); PasteBuffer(Rotate,3) | menu-default.lht |
| b s b |
Break buffer subcircuits to pieces PasteBuffer(Restore) | menu-default.lht |
| b s l d |
in multiple footprint files SaveLib(dir, buffer) | menu-default.lht |
| b s l f |
in a single lib file SaveLib(file, buffer) | menu-default.lht |
| b s p |
Break buffer padstacks to pieces PadstackBreakup(buffer) | menu-default.lht |
| b s p-shift |
Save buffer padstack to file PadstackSave(Buffer) | menu-default.lht |
| b s s |
Save buffer subcircuit to file Save(PasteBuffer) | menu-default.lht |
| c-ctrl |
Copy selection to buffer GetXY(Click to set the snap point for this buffer); PasteBuffer(Clear); PasteBuffer(AddSelected); Unselect(All); Tool(buffer) | menu-default.lht |
| c c |
Clear/reset lookup Connection(Reset); Display(Redraw) | menu-default.lht |
| c d |
Del/Remove Connected Atomic(Save); Connection(Reset); Atomic(Restore); Unselect(All); Atomic(Restore); Connection(Find); Atomic(Restore); Select(Connection); Atomic(Restore); RemoveSelected(); Atomic(Restore); Connection(Reset); Atomic(Restore); Unselect(All); Atomic(Block) | menu-default.lht |
| c e |
Erase rats nest DeleteRats(AllRats) | menu-default.lht |
| c f |
Find Connections Connection(Reset); Connection(Find) | menu-default.lht |
| c l |
List all rats ListRats(View) | menu-default.lht |
| c r-shift |
Optimize rats nest - autorouter Atomic(Save); DeleteRats(AllRats); Atomic(Restore); AddRats(AllRats, manhattan); Atomic(Close) | menu-default.lht |
| c r |
Optimize rats nest Atomic(Save); DeleteRats(AllRats); Atomic(Restore); AddRats(AllRats); Atomic(Close) | menu-default.lht |
| c s |
Select shortest rat AddRats(Close) | menu-default.lht |
| delete |
Remove object Tool(Save); Tool(remove); Tool(Press); Tool(Restore) | menu-default.lht |
| down |
Step Down Cursor(Warp,0,1,grid) | menu-default.lht |
| down-ctrl |
Scroll Down Scroll(down) | menu-default.lht |
| down-shift |
Step +Down Cursor(Pan,0,50,view) | menu-default.lht |
| e a p |
Apply Pen to object ApplyPen() | menu-default.lht |
| e c |
Copy selection to buffer GetXY(Click to set the snap point for this buffer); PasteBuffer(Clear); PasteBuffer(AddSelected); Unselect(All); Tool(buffer) | menu-default.lht |
| e d |
Remove object Tool(Save); Tool(remove); Tool(Press); Tool(Restore) | menu-default.lht |
| e f |
Object flags... FlagEdit() | menu-default.lht |
| e g c |
Clearance +2 mil ChangeClearSize(Object,+2,mil) | menu-default.lht |
| e g c-shift |
Clearance -2 mil ChangeClearSize(Object,-2,mil) | menu-default.lht |
| e g d |
ChangeDrill +5 mil ChangeDrillSize(Object,+5,mil) | menu-default.lht |
| e g d-shift |
ChangeDrill -5 mil ChangeDrillSize(Object,-5,mil) | menu-default.lht |
| e g g |
Edit padstack geometry/prototype padstackedit | menu-default.lht |
| e g s |
ChangeSize +5 mil ChangeSize(Object,+5,mil) | menu-default.lht |
| e g s-shift |
ChangeSize -5 mil ChangeSize(Object,-5,mil) | menu-default.lht |
| e g y |
ChangeSizes to Route style ChangeSizes(Object,style,mil) | menu-default.lht |
| e i |
Flip Object Flip(Object) | menu-default.lht |
| e j |
ChangeJoin Object ChangeJoin(Object) | menu-default.lht |
| e l |
Move to current layer MoveToCurrentLayer(Object) | menu-default.lht |
| e o |
Change font... FontSel(Object) | menu-default.lht |
| e p |
Object Properties... PropEdit(selection) | menu-default.lht |
| e r |
Change refdes ChangeName(Refdes) | menu-default.lht |
| e s b |
Layer bindings... LayerBinding() | menu-default.lht |
| e s e |
External editor... GetXY(Click on the subcircuit to edit); extedit(object) | menu-default.lht |
| e s r |
Refdes ChangeName(Subc) | menu-default.lht |
| e s s |
Set Same Style SetSame() | menu-default.lht |
| e s x |
Convert to extended object... ExtobjConvFrom(Object, @gui) | menu-default.lht |
| e t |
Edit text or terminal ID... ChangeName(Object) | menu-default.lht |
| e v |
Paste buffer to layout Tool(buffer) | menu-default.lht |
| e x |
Cut selection to buffer GetXY(Click to set the snap point for this buffer); PasteBuffer(Clear); PasteBuffer(MoveSelected); Tool(buffer) | menu-default.lht |
| e y |
Cycle object being dragged CycleDrag() | menu-default.lht |
| enter |
Click (left) Tool(Press); Tool(Release) | menu-default.lht |
| escape |
Cancel Tool(Escape) | menu-default.lht |
| f1 |
Via Tool(via) | menu-default.lht |
| f10 |
Thermal Tool(thermal) | menu-default.lht |
| f11 |
Arrow Tool(arrow) | menu-default.lht |
| f12 |
Lock Tool(lock) | menu-default.lht |
| f2 |
Line Tool(line) | menu-default.lht |
| f3 |
Arc Tool(arc) | menu-default.lht |
| f4 |
Text Tool(text) | menu-default.lht |
| f5 |
Rectangle Tool(rectangle) | menu-default.lht |
| f6 |
Polygon Tool(poly) | menu-default.lht |
| f7 |
Buffer Tool(buffer) | menu-default.lht |
| f7-shift |
Rotate buffer 90 deg CCW (left) Tool(buffer); PasteBuffer(Rotate,1) | menu-default.lht |
| f8 |
Del/Remove Tool(remove) | menu-default.lht |
| f9 |
Rotate Tool(rotate) | menu-default.lht |
| f a |
Save Layout As... Save(LayoutAs) | menu-default.lht |
| f c |
Export with CAM job... cam() | menu-default.lht |
| f e |
Export layout... ExportGUI() | menu-default.lht |
| f f s |
Import schematics... ImportSch() | menu-default.lht |
| f l |
Load layout... Load(Layout) | menu-default.lht |
| f n |
Start New Layout New() | menu-default.lht |
| f o |
Load layout... Load(Layout) | menu-default.lht |
| f p |
Print layout... Print() | menu-default.lht |
| f q |
Quit Program Quit() | menu-default.lht |
| f r |
Revert Load(Revert,none) | menu-default.lht |
| f s |
Save Layout Save(Layout) | menu-default.lht |
| f x o |
Order PCB OrderPCB(gui) | order-menu.lht |
| f x p |
netlist patch for back annotation SavePatch() | menu-default.lht |
| g b |
Previous grid Grid(down) | menu-default.lht |
| g c |
Custom grid Grid(ask) | menu-default.lht |
| g d |
Grid *2 SetGrid(*2) | menu-default.lht |
| g f |
Next grid Grid(up) | menu-default.lht |
| g h |
Grid /2 SetGrid(/2) | menu-default.lht |
| g i |
mil SetUnits(mil) | menu-default.lht |
| g l |
Enable local grid conf(toggle, editor/local_grid/enable, design) | menu-default.lht |
| g m |
mm SetUnits(mm) | menu-default.lht |
| g r |
Realign grid Display(RealignGrid) | menu-default.lht |
| g v |
Enable visible grid conf(toggle, editor/draw_grid, design) | menu-default.lht |
| i a |
About... About() | menu-default.lht |
| i c i |
Data integrity check Integrity() | menu-default.lht |
| i c p |
Preferences... preferences | menu-default.lht |
| i c r |
Re-scan the footprint library fp_rehash() | menu-default.lht |
| i d |
Generate drill summary Report(DrillReport) | menu-default.lht |
| i f |
Report found padstacks Report(FoundPins) | menu-default.lht |
| i r |
Generate object report ReportObject() | menu-default.lht |
| insert |
Insert Point Tool(insert) | menu-default.lht |
| j h |
Scroll Left Scroll(left) | menu-default.lht |
| j j |
Scroll Down Scroll(down) | menu-default.lht |
| j k |
Scroll Up Scroll(up) | menu-default.lht |
| j l |
Scroll Right Scroll(right) | menu-default.lht |
| k h |
Step Left Cursor(Warp,-1,0,grid) | menu-default.lht |
| k j |
Step Down Cursor(Warp,0,1,grid) | menu-default.lht |
| k k |
Step Up Cursor(Warp,0,-1,grid) | menu-default.lht |
| k l |
Step Right Cursor(Warp,1,0,grid) | menu-default.lht |
| k r |
Click (right) Tool(Release); Popup(popup-obj, obj-type) | menu-default.lht |
| k space |
Click (left) Tool(Press); Tool(Release) | menu-default.lht |
| l h |
all layers off ToggleView(all, vis, clear) | menu-default.lht |
| l k |
Select previous layer LayerByStack(Select, Prev) | menu-default.lht |
| l l |
Select next layer LayerByStack(Select, Next) | menu-default.lht |
| l v |
all layers on ToggleView(all, vis, set) | menu-default.lht |
| left |
Step Left Cursor(Warp,-1,0,grid) | menu-default.lht |
| left-ctrl |
Scroll Left Scroll(left) | menu-default.lht |
| left-shift |
Step +Left Cursor(Pan,-50,0,view) | menu-default.lht |
| m c c |
Crosshair shows style/object clearance conf(toggle, editor/show_drc, design) | menu-default.lht |
| m c o |
Orthogonal moves conf(toggle, editor/orthogonal_moves, design) | menu-default.lht |
| m c p |
Crosshair snaps to padstacks conf(toggle, editor/snap_pin, design) | menu-default.lht |
| m c s |
Crosshair snaps to off-grid points on lines conf(toggle, editor/snap_offgrid_line, design) | menu-default.lht |
| m c u |
Crosshair snaps to subcircuit origin conf(toggle, editor/snap_subc_origin, design) | menu-default.lht |
| m d a |
Show autorouter trials conf(toggle, editor/live_routing, design); Display(Redraw) | menu-default.lht |
| m d c |
Check polygons conf(toggle, editor/check_planes, design); Display(Redraw) | menu-default.lht |
| m d d |
poly as-drawn frame annotation conf(toggle, editor/as_drawn_poly, design); Display(Redraw) | menu-default.lht |
| m d e |
Indicate edit points on hover conf(toggle, plugins/ch_editpoint/enable, design) | ch_editpoint-menu.lht |
| m d h |
Highlighting on line, arc points conf(toggle, editor/highlight_on_point, design); Display(Redraw) | menu-default.lht |
| m d o |
Object list popup conf(toggle, editor/click_objlist, design) | menu-default.lht |
| m d p |
Thin draw poly conf(toggle, editor/thin_draw_poly, design); Display(Redraw) | menu-default.lht |
| m d r |
Reset | menu-default.lht |
| m d t |
Thin draw conf(toggle, editor/thin_draw, design); Display(Redraw) | menu-default.lht |
| m d w |
Wireframe draw conf(toggle, editor/wireframe_draw, design); Display(Redraw) | menu-default.lht |
| m f h |
Hide floaters conf(toggle, editor/hide_names, design) | menu-default.lht |
| m f l |
Lock floaters display(togglelocknames) | menu-default.lht |
| m f o |
Only floaters display(toggleonlynames) | menu-default.lht |
| m k s |
Loose subcircuits (no subc lock) subc(loose, toggle) | menu-default.lht |
| m l + |
Line Tool size +5 mil SetValue(LineSize,+5,mil) | menu-default.lht |
| m l - |
Line Tool size -5 mil SetValue(LineSize,-5,mil) | menu-default.lht |
| m l a |
'All-direction' lines conf(toggle, editor/all_direction_lines, design) | menu-default.lht |
| m l c |
New lines, arcs clear polygons conf(toggle, editor/clear_line, design) | menu-default.lht |
| m l d |
Auto enforce style clearance conf(toggle, editor/auto_drc, design) | menu-default.lht |
| m l f |
Cycle line clip/refraction Display(CycleClip) | menu-default.lht |
| m l m |
Automatic trace merging conf(toggle, editor/trace_auto_merge, design) | menu-default.lht |
| m o b |
black current group conf(toggle, appearance/black_current_group, design) | menu-default.lht |
| m o i |
Invisible-color on other groups conf(toggle, appearance/invis_other_groups, design) | menu-default.lht |
| m p c |
New polygons clear polygons conf(toggle, editor/clear_polypoly, design) | menu-default.lht |
| m p f |
New polygons are full ones conf(toggle, editor/full_poly, design) | menu-default.lht |
| m p i |
Polygon clip inhibit (toggle) ClipInhibit(toggle) | menu-default.lht |
| m r m |
Rubber band keeps middle line dir conf(toggle, editor/rubber_band_keep_midlinedir, design) | menu-default.lht |
| m r r |
Rubber band mode conf(toggle, editor/rubber_band_mode, design) | menu-default.lht |
| m t + |
Text Tool scale +10 mil SetValue(TextScale,+10,mil) | menu-default.lht |
| m t - |
Text Tool scale -10 mil SetValue(TextScale,-10,mil) | menu-default.lht |
| n-ctrl |
Start New Layout New() | menu-default.lht |
| n c f |
claim net on found ClaimNet(found) | menu-default.lht |
| n c o |
claim net by object ClaimNet(object) | menu-default.lht |
| n c s |
claim net on selected ClaimNet(selected) | menu-default.lht |
| n l k |
Visual length, clear NetLength(clear) | menu-default.lht |
| n l l |
Netlist dialog, refresh lengths NetlistDialog(); NetlistDialog(RefreshNetLens) | menu-default.lht |
| n l o |
Visual length, from object NetLength(object) | menu-default.lht |
| p m p |
Manage plugins... ManagePlugins() | menu-default.lht |
| p m s |
Manage scripts... BrowseScripts() | menu-default.lht |
| p p c |
Polygon Close Polygon(Close) | menu-default.lht |
| p p p |
Polygon PreviousPoint Polygon(PreviousPoint) | menu-default.lht |
| q-ctrl |
Quit Program Quit() | menu-default.lht |
| r r + |
Route radius +0.5 conf(delta, editor/route_radius, +0.5, design) | menu-default.lht |
| r r - |
Route radius -0.5 conf(delta, editor/route_radius, -0.5, design) | menu-default.lht |
| r r m |
Route radius -0.5 conf(delta, editor/route_radius, -0.5, design) | menu-default.lht |
| r r p |
Route radius +0.5 conf(delta, editor/route_radius, +0.5, design) | menu-default.lht |
| r s c |
Connect RbsConnect() | rbs_routing-menu.lht |
| r s s |
Stretch RbsStretch() | rbs_routing-menu.lht |
| right |
Step Right Cursor(Warp,1,0,grid) | menu-default.lht |
| right-ctrl |
Scroll Right Scroll(right) | menu-default.lht |
| right-shift |
Step +Right Cursor(Pan,50,0,view) | menu-default.lht |
| s-ctrl |
Save Layout Save(Layout) | menu-default.lht |
| s-ctrl-shift |
Save Layout As... Save(LayoutAs) | menu-default.lht |
| s a a |
Select all visible objects Select(All) | menu-default.lht |
| s a c |
Select all found objects Select(Connection) | menu-default.lht |
| s a p |
Apply Pen ApplyPen(selected) | menu-default.lht |
| s b p |
Break selection padstack to pieces PadstackBreakup(selected) | menu-default.lht |
| s b s |
Break selection subcircuits to pieces PasteBuffer(Push); PasteBuffer(5); PasteBuffer(Clear); PasteBuffer(AddSelected); RemoveSelected(); PasteBuffer(Restore); PasteBuffer(ToLayout, crosshair); PasteBuffer(Clear); PasteBuffer(Pop) | menu-default.lht |
| s c e |
Convert selection to extended object... ExtobjConvFrom(Selected, @gui) | menu-default.lht |
| s c p |
Convert selection to padstack PadstackConvert(selected); Tool(buffer) | menu-default.lht |
| s c s |
Convert selection to subcircuit Select(ConvertSubc) | menu-default.lht |
| s e d |
DC power EmsDcpower() | emsim-menu.lht |
| s f |
Move selected subcircuits to other side Flip(SelectedElements) | menu-default.lht |
| s i |
Invert selection Select(Invert) | menu-default.lht |
| s k a-shift |
Select all unlocked objects query(select, "@.p.flag.lock == 0 && isvoid(@.subc)") | menu-default.lht |
| s k a |
Select all locked objects query(select, "@.p.flag.lock == 1 && isvoid(@.subc)") | menu-default.lht |
| s k k |
Lock selected objects propset(selection, p/flags/lock, 1) | menu-default.lht |
| s k l |
List locked objects query(view, "@.p.flag.lock == 1 && isvoid(@.subc)") | menu-default.lht |
| s k p-shift |
Select unlocked polygons query(select, "@.p.flag.lock == 0 && @.type == POLYGON") | menu-default.lht |
| s k p |
Select locked polygons query(select, "@.p.flag.lock == 1 && @.type == POLYGON") | menu-default.lht |
| s k s-shift |
Select unlocked subcircuits query(select, "@.p.flag.lock == 0 && @.type == SUBC") | menu-default.lht |
| s k s |
Select locked subcircuits query(select, "@.p.flag.lock == 1 && @.type == SUBC") | menu-default.lht |
| s k u |
Unlock selected objects propset(selection, p/flags/lock, 0) | menu-default.lht |
| s l |
Move selected objects to current layer MoveToCurrentLayer(Selected) | menu-default.lht |
| s p |
Edit properties propedit(selection) | menu-default.lht |
| s r |
Remove selected objects RemoveSelected() | menu-default.lht |
| s s |
Advanced search and select SearchDialog() | menu-default.lht |
| s u a |
Unselect all objects Unselect(All) | menu-default.lht |
| s u c |
Unselect all found objects Unselect(Connection) | menu-default.lht |
| s x s |
cross-select object under cursor XProbeSend(object, select) | suite-menu.lht |
| s x u |
cross-unselect object under cursor XProbeSend(object, unselect) | suite-menu.lht |
| s x v |
cross-view object under cursor XProbeSend(object, show) | suite-menu.lht |
| s z s |
cross-select selected objects XProbeSend(selection, select) | suite-menu.lht |
| s z u |
cross-unselect selected objects XProbeSend(selection, unselect) | suite-menu.lht |
| s z v |
cross-view selected objects XProbeSend(selection, show) | suite-menu.lht |
| space |
Arrow Tool(arrow) | menu-default.lht |
| t a |
Arc Tool(arc) | menu-default.lht |
| t b |
Buffer Tool(buffer) | menu-default.lht |
| t c |
Copy Tool(copy) | menu-default.lht |
| t d |
Del/Remove Tool(remove) | menu-default.lht |
| t e |
Thermal Tool(thermal) | menu-default.lht |
| t h |
Polygon Hole Tool(polyhole) | menu-default.lht |
| t i |
Insert Point Tool(insert) | menu-default.lht |
| t k |
Lock Tool(lock) | menu-default.lht |
| t l |
Line Tool(line) | menu-default.lht |
| t m |
Move Tool(move) | menu-default.lht |
| t n |
Arrow Tool(arrow) | menu-default.lht |
| t o |
Rotate Tool(rotate) | menu-default.lht |
| t p |
Polygon Tool(poly) | menu-default.lht |
| t r |
Rectangle Tool(rectangle) | menu-default.lht |
| t t |
Text Tool(text) | menu-default.lht |
| t v |
Via Tool(via) | menu-default.lht |
| tab |
Flip up/down SwapSides(V) | menu-default.lht |
| tab-ctrl |
Spin 180 degrees SwapSides(R) | menu-default.lht |
| tab-ctrl-shift |
Swap Sides SwapSides() | menu-default.lht |
| tab-shift |
Flip left/right SwapSides(H) | menu-default.lht |
| u c |
Clear undo-buffer Undo(ClearList) | menu-default.lht |
| u d |
Undo dialog (for debugging) UndoDialog() | menu-default.lht |
| u r |
Redo last undone operation Redo() | menu-default.lht |
| u u |
Undo last operation Undo() | menu-default.lht |
| up |
Step Up Cursor(Warp,0,-1,grid) | menu-default.lht |
| up-ctrl |
Scroll Up Scroll(up) | menu-default.lht |
| up-shift |
Step +Up Cursor(Pan,0,-50,view) | menu-default.lht |
| v c |
Center cursor Center() | menu-default.lht |
| v f |
Zoom Extents Zoom() | menu-default.lht |
| v n |
Show padstack numbers in a subc Display(PinOrPadName) | menu-default.lht |
| v r g |
Reset GUI | menu-default.lht |
| v r v |
Reset View | menu-default.lht |
| v s c |
user configured Display(SubcID) | menu-default.lht |
| v s f |
footprint Display(SubcID,"%a.footprint%") | menu-default.lht |
| v s r |
refdes Display(SubcID, "%a.refdes%") | menu-default.lht |
| v s s |
refdes+value Display(SubcID,"%a.refdes%\\n%a.value%") | menu-default.lht |
| v s v |
value Display(SubcID,"%a.value%") | menu-default.lht |
| v t c |
user configured Display(TermID) | menu-default.lht |
| v t n |
name Display(TermID, "%a.name%") | menu-default.lht |
| v t s |
term+name Display(TermID, "%a.term%,%a.name%") | menu-default.lht |
| v t t |
term Display(TermID, "%a.term%") | menu-default.lht |
| w a |
About... About() | menu-default.lht |
| w b |
Back annotation NetlistPatchDialog() | menu-default.lht |
| w d |
DRC Check DRC() | menu-default.lht |
| w f |
Font selector FontSel() | menu-default.lht |
| w l |
Library LibraryDialog() | menu-default.lht |
| w m |
Message Log LogDialog() | menu-default.lht |
| w n |
Netlist NetlistDialog() | menu-default.lht |
| w p |
Pinout Display(Pinout) | menu-default.lht |
| w v |
Viewport ViewPortDialog() | menu-default.lht |
| y-ctrl |
Redo last undone operation Redo() | menu-default.lht |
| z-ctrl |
Undo last operation Undo() | menu-default.lht |
| z e |
Zoom Extents Zoom() | menu-default.lht |
| z f |
Zoom to found ZoomTo(found) | menu-default.lht |
| z s |
Zoom to selection ZoomTo(selected) | menu-default.lht |
| z x |
Zoom Out 20% Zoom(+1.2) | menu-default.lht |
| z z |
Zoom In 20% Zoom(-1.2) | menu-default.lht |
| | |
Wireframe draw conf(toggle, editor/wireframe_draw, design); Display(Redraw) | menu-default.lht |